Statistical Optimizations of Fermentation Factors on Bioethanol
Production from Mahua Flower (Madhuca indica) with
Saccharomyces cerevisiae by Response Surface Methodology in
|Publishing Date||March 29,2016|
|Type of Paper||Research Article|
|Mode of Access||Open Access|
|Author||1. Dr.Dovari.Surndra Nadh Benarji 2. Prof. Chityala Ayyanna|
|Affiliation||1. Department of Biotechnology,Acharya Nagarjun University,Guntur,522510 2. Director Department of Biotechnology,Al-Ameer College of Engineering and Information Technology Vizag,5310137|
The aim of the present investigation is to enhance the bioethanol production from agricultural feed stocks through fermentation process. To bring out facts, experiments were conducted on the biochemical analysis of Mahua flower (Madhuca indica) for its suitability as a raw material and optimizations of fermentation conditions using response surface methodology. The results of fermentation processes on bioethanol productions were compared and tabulated. From the data, it was observed that Saccharomyces cerevisiae-3190 NCIM is high bioethanol tolerant, acid resistant, and is able to produce high yields of bioethanol in high gravity medium. The optimum conditions such as pH 4.9, temperature 31.43 0C, agitation 117.28 RPM, and ammonium sulphate (NH4)2SO4) of 0.629 mg.l-1 were obtained on bioethanol production with statistical optimizations. The yeast strain could produce 150.562g.l-1 and 195.284 g.l-1 with the substrate concentration of 360 g.l-1 and 409 g.l-1 after 48 hours by medium-I and medium-II respectively.
Bioethanol, Fermentation, RSM, Bioethanol Method, Gas Chromatography.
Ethanol is an ancient organic solvent which next to the water and is named as “Bioethanol”, after its production through fermentation process using microorganisms. Conversion of sugars into ethanol is one of the earliest anaerobic organic reactions employed by humanity. Several authors reported that the attention has been devoted to the conversion of various substrates such as molasses, sugar cane, sorghum, potato, cassava, cashew apple juice, fruit juices and corn, wheat, pearl millet, rice to fuel bioethanol using bacterial and yeast cells. The industrial production of ethanol and commercial use of yeasts started at the end of the 19th century after their identification and isolation by Louis Pasteur. In 1908, Henry Ford has designed a fuel with a mixture of Gasoline and Alcohol and further it was referred as “The fuel of the future” in the year 1925 (Ravindra, 2007). Ethanol (C2 H5 OH) is pure in color, volatile flammable and non toxic. Worldwide fuel prices are rising due to increase in demand by the population (Dake, et al, (2010). It has a molecular weight of 46.07, melting point of -115 0C, boiling point of 78 0C and specific gravity of 0.79 GM/ml at 20 0C. The oxygenated bio-fuels like biodiesel and bioethanol are an effective substitute for renewable fuels and reduce particulate matter from in-use diesel vehicles (Krishna swamy, et al, 2012).
Substrate Mahua flower (Madhuca indica) belongs to the family Sapotaceae. It is a medium sized to large deciduous tree, usually with a short bole and rounded crown and found throughout the greater part of India up to an altitude of 1200m. It is usually found in mixed deciduous forest, usually of dry type, and grows on rocky and sandy soil and flourishes on the Deccan plateau. It is common throughout the deciduous forest in central India, Madhya Pradesh, Maharashtra, Gujarat, Orissa, Chota Nagpur, and Andhra Pradesh (Wealth of India, 1962). Mahua flower contains total fermentable sugars of 731.343µg/ml, Moisture content of 17 %, Reducing sugars of 18%, Protein of 4.6 mg and Fat of 0.5 %. A gram of glucose can be converted to 0.511 grams of ethanol (Maiorella, et al, 1981). The stoichiometric glucose conversion to bioethanol in the presence of yeast cells can be represented as follows:
C6H12O6 (180 g.mol) →→→→ 2C2 H5 OH (92 g.mol) + 2CO2 (88 g.mole)
Optimization of medium constituents by laboratory method is a single–dimensional search involving change of one variable while fixing the others at a certain level is laborious and time consuming, especially when the number of variables is in large. Therefore, an alternative and potential method in microbial system is the function of statistical methods. Hence, the present optimization studies were carried out with Box-Wilson (Box and Wilson, 1951) response surface methodology using software Statistica8.
Materials and Methods
Yeast and Bacterial strains such as Saccharomyces cerevisiae-3190 NCIM, S.cerevisiae-171 MTCC, K.thermotolerance-30 MTCC, S.cerevisiae-3288 NCIM, K.marxianus-1389 MTCC, Z.mobilis-92 MTCC, E.coli and S.cerevisiae-463 MTCC, which are obtained from National Collection of Industrial Microorganisms (NCIM), National Chemical Laboratories, Pune and (MTCC) Microbial Type Culture Collection, Chandigarh, India) cultures were tested for bioethanol production.
Total sugars in Mahua flowers extract (MFE) estimated by Anthrone method (Yemm and Willis, 1954), Moisture content by Association of Official Agricultural Chemists (AOAC, 2000), Method No: 930.15, reducing sugars by Miller method (1959), protein by Lowry’s method (1951), and Fat by American association of cereal chemists (AACC, Method: 30-25, 1983). Determination of total cell count by American public health association (APHA Method, 1967). Estimation of total viable cell count was determined by methylene blue reagent (Bonara and Mares (1982).
Preparation of bacterial culture medium
Bacterial culture medium was prepared using beef extract of 3 g.l-1; peptone, 5 g.l-1; sodium chloride of 8 g.l-1 and 15 grams of Agar were added to 1000 ml of distilled water in 2 litre Erlenmeyer flask. The pH of the medium was adjusted to 7.5 using 1 N HCL and 1 N NaOH with the aid of pH Meter (Systronics). Then, the medium was allowed to sterilize at 121 0C for 30 minutes. Then, 10 ml of sterilized medium was aseptically transferred to the culture tubes and rotated at 450 for 25 minutes to develop agar slopes. After the solidification completed, one loopfull of original culture of bacterial strains were aseptically streaked on agar slopes and tightly capped with non-adsorbent cotton. Then, these agar slants were incubated at 25 0C for 48 hours of growth period.
Preparation of yeast culture medium
The yeast culture medium was prepared in 2 litre Erlenmeyer flasks containing glucose, yeast extract, malt extract and peptone (GYMP) in 1 litre of distilled water and pH was adjusted to 6 using 1 N HCL and 1 N NaOH .The medium was autoclaved at 1210C for about 30 minutes.
After autoclave was completed, 10 ml of medium was aseptically transferred to petri plates and 30 ml tubes. Then, the original cultures of yeast were aseptically inoculated with loop on agar slopes. Using this medium composition, cultures were incubated at 300C for 48 hours. For every 30 days, yeast culture was freshly prepared for maintaining cell viability and the total experiments were carried out with freshly prepared nutrient agar medium and nutrient broth medium.
Response surface methodology
Response surface methodology (RSM) is one of the suitable methods for identifying the effect of individual variables and optimizing the conditions for a multivariable system efficiently. Multiple regression and correlation analysis are used as tools to assess the effects of two or more independent factors on the dependent variables (Ratnam, et al., 2003). The central composite design (CCD) with 3k factorial design was applied for the optimization of fermentation conditions on bioethanol production. Three different levels such as low concentration level (-1), Middle level (0) and High level (+1) and three independent variables represented as X1, X2, X3 and dependent variable is the production of bioethanol (g.l-1) were applied to CCD. Recently, many statistical experimental design methods have been employed in bioprocess optimization. Two axial points on the axis of each design variable at a distance of α from the design centre were applied. Thus the total number of design points in central composite design (CCD) consisting of k variables are given as follows
γi = β̥+β1x1+ β2x2+ β2x3+ β11 x12+ β22 x22+ β33x32+ β12x1x2+ β13x1x3+β23x2x3
Where, Yi is Predicted Response; X1, X2 and X3 are Independent Variables; β̥ is Offset term; β1, β2, β3 are Linear effects; β11, β22 and β33 are Squared effects and β12, β13, β23 are Interaction terms.
Fermentation with 5 litre bioreactor
Bioreactor (B-Lite, Sartorious Private Limited, Mumbai, India) is batch scale bioreactor that can ferment up to 5 Litres of fermentative medium. In the present study, 2 litres of Mahua fermentative medium was used for bioethanol production under controlled conditions like pH, temperature, and agitation. During the batch fermentation process, bioreactor was sterilized at 121 0C for 15 minutes.
Total content of bioethanol in fermented sample were determined by gas chromatograph (GC). Gas chromatography method for bioethanol production was developed based on the dilutions used in British pharmacopeia (2007).
Bioethanol (%)=( Peak Area of Biothanol)/( Peak Area of n-Butanol) x (Wt of Std)/(Std Volume ) x (Sample Volume)/(wt.of sample) x Std Potency
Peak Area of Bioethanol = peak hight of chromatogram of bioethanol
Peak Area of n- Butanol = peak hight of chromatogram of n-butanol
Sample Volume = sample dilution
Wt of Std = weight of the standard
Std Volume = standard volume
Wt of sample = weight of sample
Std Potency = standard concentration of bioethanol
Results & Discussion
During the process of fermentations, screening of various microorganisms was carried on bioethanol productions. The microorganisms such as Saccharomyces cerevisiae-171 MTCC, Kluyveromyces thermotolerance-30 MTCC, S.cerevisiae-3288 NCIM, S.cerevisiae-3190 NCIM, K.marxianus-1389 MTCC, Zymomonas mobilis-92 MTCC, Escherichia coli and S.cerevisiae-463 produced bioethanol concentrations of 36.437g.l-1, 35.573 g.l-1, 41.241 g.l-1, 43.865 g.l-1, 40.531 g.l-1, 39.657 g.l-1, 37.559 g.l-1, and 41.327 g.l-1 respectively. Amongst, S.cerevisiae-3190 (NCIM) produced maximum bioethanol yield was 43.865 g.l-1 after 48 hours of fermentation than other yeast and bacterial cells. From the results, it was found that the yeast strain S.cerevisiae-3190 (NCIM) is efficient and used throughout the optimizations of fermentative conditions on bioethanol productions. The result shown in figure: 1.The initial standardization of fermentative conditions such as physico-chemical and nutritional factors were carried out using S.cerevisiae-3190 (NCIM) with 5l bioreactor (B-Lite Sartorious limited, Mumbai).
The maximum bioethanol yields obtained by the standard optimizations of fermentative conditions (Medium-I) were 98.14 g.l-1 at 400 g.l-1 of substrate concentration , 103.15 g.l-1 at 30 0C of temperature, 108.69g.l-1 at pH 5, 110.63 g.l-1 at 120 RPM of agitation 111.19 g.l-1 at 8v/v of inoculum volume, 112.98g.l-1 at 0.6 g.l-1 of ammonium sulphate (NH4)2SO4, 110.189 g.l-1 at 0.5 g.l-1 of copper chloride (CuCl2), 116.64 g.l-1 at 0.06 g.l-1 of manganese chloride (MnCl2.4H2O), 118.0 g.l-1 at 0.4 g.l-1 of magnesium chloride (MgCl2.6H2O), 114.75 g.l-1 at 50 mg.l-1 of zinc sulphate (ZnSO4.7H2 O), 115.68 g.l-1 at 24 mg.l-1 of biotin, 114.36 g.l-1 at 0.150 of g.l-1 of proline, 119.342 g.l-1 at 5.0 g.l-1 sodium di hydrogen phosphate (NaH2PO4), 117.653 g.l-1 at 5 g.l-1 of ethylene di-amine tetraacetic acid (EDTA), 116.981 g.l-1 2.0 g.l-1 of potassium phosphate (K2HPO4), 115.947 g.l-1 at 0.06 g.l-1 of calcium chloride (CaCl2), 118.635 g.l-1 at 80 mg.l-1 of cobalt chloride (CoCl2), 102.721 g.l-1 at 0.5 g.l-1, oxygen (O2) at 0.3 mg.l-1 of ferrous sulphate (Fe2(SO4)3.H2O), 93.641 g.l-1 at 0.10 g.l-1 of sodium chloride (NaCl2), 100.634 g.l-1 at 3.0 g.l-1 of peptone, 114.735 g.l-1 at 2.5 g.l-1 of urea and 118.462 g.l-1 at 1.5 g.l-1 of yeast extract. Under these optimum concentrations of medium-I, bioethanol yield obtained was 150.562g.l-1 at the fermentation efficiency of 3.1367g.l-1.h-1 and the percentage of yield of bioethanol was 73.66 %. Elena Patrascu, et al., (2009) who have been reported that some selected yeast strains can produce bioethanol yields up to 15 % or higher. The viable yeast cells were found to be 98 % after 48 hours of fermentation time. The experimental results are shown in figure. no. 2.
Statistical optimizations of fermentative conditions (Medium-II) were conducted in order to enhance the bioethanol yields with S.cerevisiae-3190 (NCIM) response surface methodology (RSM) with software Statistica8. The Three factors at a time was applied using central composite design and eight central composite designs were developed based on the standard optimization of fermentative factors of medium-I. The maximum bioethanol concentrations were produced with statistical optimum fermentative conditions: the experiments on fermentation conditions optimum with substrate concentration of 409.916 g.l-1, temperature of 31.43 0C and pH of 4.9 of central composite design-I produced bioethanol yield was 113.570 g.l-1. The surface plot bioethanol production was shown in figure no. 3. The optimum concentrations of central composite design-II produced bioethanol yield was 121.878 g.l-1 with inoculum volume of 9.000 v/v, agitation of 117.28 RPM and inoculum age of 53.66 hours (figure.no. 4).
The statistical optimization of fermentation conditions with ammonium sulphate (NH4)2SO4) of 0.629 mg.l-1, copper chloride (CuCl2) of 0.522 mg.l-1 and manganese chloride (MnCl2.4H2O) of 0.061 mg.l-1 produced bioethanol yield was 128.763 g.l-1 (figure. no. 5). The optimum concentrations of central composite design-IV with magnesium chloride (MgCl2.6H2O) of 0.430 g.l-1, zinc sulphate (ZnSO4.7H2 O) of 54.021 mg.l-1, biotin of 22.453 mg.l-1 produced bioethanol yield was 131.281 g.l-1(figure. no. 6).
Figure no.1: Screening of microorganisms
Figure no.2: Bioethanol production with medium-I
Figure no.3: statistical optimizations of substrate concentration and temperature with pH was kept constant on Bioethanol production.
Figure no.4: statistical optimizations of inoculum volume and inoculum age with agitation was kept constant on Bioethanol production.
Figure no.5: statistical optimizations of copper chloride and ammonium sulphate with manganese was kept constant on Bioethanol production.
Figure no.6: Figure no.7: statistical optimizations of Zinc and magnesium with biotin was kept constant on Bioethanol production.
Figure no.8: statistical optimizations of EDTA and phosphorous with proline was kept constant on bioethanol production.
Figure no.9: statistical optimizations of oxygen and ferrous sulphate with cobalt was kept constant on bioethanol production.
Figure no.10: statistical optimizations of peptone and yeast extract with urea was kept constant on bioethanol production.
Table No: 11. Statistical optimum fermentation conditions of central composite designs on Bioethanol productions
Figure no.12: bioethanol production with medium-II
From the data of experiments, it can be concluded that the yeast strain Saccharomyces cerevisiae-3190 is resistant to acidic conditions, osmotic stresses by very high gravity medium and high ethanol tolerant. Mahua flower (Madhuca indica) was proved as a suitable substrate for bioethanol production. One million tonns of Mahua flower could produce 3, 48,303 Litres of bioethanol. When bioethanol used as blend in petrol, thus replace 3,48,303 Litres of petrol in India. To meet the required fuel quantity, bioethanol production through fermentation process in industrial scale is the only alternative method to avoid fuel crisis. The statistical optimizations of fermentation conditions for bioethanol productions with Mahua flower by response surface methodology could be feasible economic bioprocess.
(Microbioz Journals,Journal of Microbiology and Biomedical Research is peer reviewed Journal of Microbiology and Biomedical Sciences )This work is licensed under a Creative Commons Attribution 3.0 Unported License.
Add: 631/63, Surendra Nagar, Mulayam Nagar, Lucknow, Uttar Pradesh, India
Mob: +(91) - 9670704431, +(91) - 8896013916